Speedi-Sleeves are thin-walled metal repair sleeves used to restore a worn or damaged running surface on a shaft. When an oil seal runs over the same position on a rotating shaft for a long period of time, a wear groove can develop. As a result, even a new oil seal may no longer seal properly and leakage can occur again.
A Speedi-Sleeve is installed over the damaged section of the shaft and creates a new, smooth sealing surface for the oil seal. In many cases, this eliminates the need to replace or rework the complete shaft. Speedi-Sleeves therefore provide a practical solution for repairing shafts in pumps, motors, gearboxes and industrial machinery.
A Speedi-Sleeve is a very thin metal sleeve that is fitted over the damaged running surface of a shaft. The sleeve then forms the new surface over which the sealing lip of the oil seal runs.
A good running surface is important for the operation of a radial shaft seal. Damage, corrosion, wear or a worn groove can prevent the sealing lip from making proper contact with the shaft. This can result in leakage.
A Speedi-Sleeve can restore the worn running surface of a shaft without having to replace the original shaft completely. The thin sleeve covers the damaged area and once again provides the sealing lip with a suitable surface to seal against.
In a rotating application, the sealing lip of an oil seal continuously runs over the same position on the shaft. Over time, this movement can gradually cause wear at this location. Contamination, insufficient lubrication, corrosion and operating conditions can further influence this wear.
Eventually, a visible or noticeable wear groove may develop. If only the oil seal is replaced, the new sealing lip may once again run over this damaged position. Replacing the seal alone will then not solve the underlying problem.
The Speedi-Sleeve covers the damaged section and creates a new running surface for the sealing lip. This allows the new oil seal to seal against a suitable surface again.
Completely replacing or reworking a damaged shaft can be time-consuming and expensive. Depending on the machine, a large part of the installation may need to be dismantled before the shaft can be removed or machined.
In suitable situations, a Speedi-Sleeve can provide a simpler alternative. The existing shaft remains in place and the damaged sealing surface is covered with a thin repair sleeve. This can reduce repair time and machine downtime.
A Speedi-Sleeve is not an oil seal itself. The sleeve repairs the running surface on which the sealing lip of the oil seal makes contact. Both components therefore have a different function within the same sealing arrangement.
An oil seal is used to seal rotating or oscillating machine components, primarily shafts. The sealing lip runs over the surface of the shaft and helps, for example, to keep lubricant inside the construction and contaminants outside.
The Speedi-Sleeve restores the contact surface between the shaft and the sealing lip. Due to its small wall thickness, in many applications the original seal size does not need to be changed.
Speedi-Sleeves can be used in machines and installations where an oil seal seals against a rotating shaft and the original running surface has become damaged or worn.
In pumps, electric motors and other drive systems, rotating shafts can show signs of wear after prolonged use at the point where the sealing lip runs. A repair sleeve can create a new sealing surface at this location.
Oil seals are also used around rotating shafts in gearboxes, transmissions and industrial drive systems. A damaged running surface can be restored with a suitable Speedi-Sleeve.
Speedi-Sleeves can also be used in various industrial machines and rotating installations where wear of the sealing surface would otherwise require repair or replacement of the shaft.
The correct Speedi-Sleeve size is selected based on the shaft diameter. Measure the shaft diameter at an undamaged position next to the worn running surface. Do not measure only inside the wear groove, as the diameter may have become smaller due to wear.
It is advisable to check the diameter at several points. The appropriate repair sleeve can then be selected based on the measured range.
In addition to the shaft diameter, check whether the width and position of the Speedi-Sleeve ensure that the sealing lip runs completely over the new running surface after installation.
For proper operation, a Speedi-Sleeve must be installed carefully. First clean the damaged running surface and remove burrs, sharp edges and other irregularities that could damage the thin sleeve during installation.
The repair sleeve is then installed evenly over the shaft using the appropriate installation tool until the new running surface is positioned correctly underneath the sealing lip.
After installation, check that the Speedi-Sleeve is correctly positioned and undamaged on the shaft. The oil seal can then be installed according to the applicable installation instructions so that the sealing lip runs over the new surface.
A Speedi-Sleeve can offer several benefits when repairing a damaged sealing surface:
Speedi-Sleeves are mainly used in combination with rotary shaft seals. Therefore, also view the range of rotary seals for other solutions for rotating shafts.
Is the running surface damaged because an oil seal has been running over the shaft for a long period of time? Also view the available oil seals. A suitable oil seal and a correctly restored running surface are both important for reliable sealing.
For applications where protection against dirt, dust and splash water is the main requirement, V-rings may also be relevant.
A Speedi-Sleeve is a thin metal repair sleeve fitted over a damaged or worn section of a shaft. This creates a new running surface for the sealing lip of an oil seal.
A Speedi-Sleeve can be used when the running surface of a rotating shaft is damaged or worn and therefore no longer provides a suitable sealing surface for the oil seal.
Due to the small wall thickness of a Speedi-Sleeve, a different oil seal size is not required in many applications. Always check the specifications of the selected repair sleeve and seal.
Measure the shaft diameter at an undamaged position next to the worn section. Also check whether the width and position of the sleeve are suitable for the running surface of the oil seal.
No. The Speedi-Sleeve restores the surface on which the seal runs. The oil seal is the component that performs the actual sealing function.
In suitable applications, yes. When mainly the sealing running surface is damaged, a Speedi-Sleeve can create a new running surface without replacing the complete shaft.
Receive personal advice or a tailored quotation from our product specialists. Fill in the form and discover which Z - Speedi-Sleeves - Nieuw best fit your needs.
Nederlands 
Deutsch 